Estimating artificial turf means turning site measurements into a workable roll layout. A takeoff, the measured materials list for a job, has to account for fibre direction, joins and cuts before the order is totalled.
Measure and sketch the finished area
Measure the proposed turf boundary rather than relying on the existing lawn outline. Measure in feet, not metres: turf is sold in feet. Draw a sketch with every measurement on it, using fixed reference points such as a patio edge, the house, doors and paths.
Split an irregular area into rectangles, work each one out and add them together. Do not average a curve. Measure the widest point of each rectangle, because that is what has to be cut from. Show beds, paving, posts and access covers as exclusions.
Separate the net area, the finished surface receiving turf, from the material ordered. Square footage is where every calculation starts, but it is not what you order. An opening within the boundary may reduce the net area without shortening the piece needed to surround it.
Complete a site evaluation for the turf project before fixing the layout. Contact BC 1 Call before digging, and follow the PGB installation guide and product instructions.
How to estimate artificial turf by roll width
Turf comes off a roll 7.5 or 15 ft wide and up to 66 ft long. Premium Nylon Putt 55 is the exception, at 13.12 ft wide by 100 ft. Every piece runs in the same direction, so a piece cannot be turned sideways to make it fit.
Work out the pieces in four steps:
- Set the pile direction. Front yards face the street; back yards face the house. Every piece runs that way.
- Count the pieces across the pile. Take 6 in off the width of every piece for trimming, so a 15 ft roll covers 14 ft 6 in and a 7.5 ft roll covers 7 ft. Divide and round up.
- Set the length along the pile. Add 6 in at each end. That is the length of every piece.
- Write the order as pieces. How many, what roll width, what length. It will always be more than the area.
Mix roll widths to save turf. A yard 20 ft across is covered by one 15 ft piece and one 7.5 ft piece (21 ft 6 in of coverage). Two 15 ft pieces would also cover it, with 8 ft of width thrown away.
Worked example. A back yard 28 ft wide and 20 ft deep is 560 sq ft. The pile runs toward the house, so 28 ft is across the pile. Two 15 ft pieces cover 29 ft, with one seam. Each piece is 20 ft plus 6 in at each end, so 21 ft. The order is 2 pieces, 15 ft by 21 ft: 630 sq ft of turf for 560 sq ft of lawn. At 30 ft wide the same yard needs a third piece. Find that out on paper, not on installation day.
Give each piece a label and record its cut length in a cutting schedule. Order the whole job at once: turf from one production run matches in colour, and turf ordered in two lots may not.
Keep pile direction consistent
Pile direction is the direction the turf fibres lean. Pieces facing different ways can appear to be different colours, even when they are the same turf. Mark an arrow on every piece and keep those arrows aligned throughout the layout. See drawing out the plan.
An offcut, material left after trimming, is useful only if it fits its new location without changing the pile direction. If a piece only fits turned around, it does not fit.
Choose seams before finalising the order
Mark every seam before accepting a layout. Choose the roll widths and layout that give the fewest joins, even when it means more offcut. Keep seams out of entrances, walkways and play areas, where foot traffic parts the fibres and the seam starts to show. If a seam lands in one, start the first piece from the other side or use a 7.5 ft piece to move the join.
Prefer side seams, along the length of the roll, over head seams, where two roll ends meet. A head seam crosses every stitch row and is harder to hide. Use one only when the layout leaves no choice. See seaming basics.
Add up the seams along their intended routes, counting each joint once. Use these lengths for the tape takeoff.
Allow for cuts without double-counting
The trimming allowance is already built into the four steps: 6 in off the width of every piece and 6 in at each end. Do not add a second waste factor on top of the finished area.
Identify unusable waste separately from offcuts assigned to another part of the job. A leftover piece should reduce the order only when the sketch shows where it fits, with matching pile direction and enough material for trimming.
Treat a curved bed as a cutting shape within a roll piece. Subtracting its area from the finished surface does not shorten the roll required.
Count infill, spikes and seam tape
Accessory quantities come from the same drawing. Keep base, edging and drainage materials as separate takeoff items.
Infill. Multiply the finished turf area by the rate for the turf, then divide by the bag weight and round up. Do not count offcuts.
- Everglades, Forest Green Elite and Juniper: 3 to 5 lbs per sq ft.
- Evergreen and Cedar: 2 to 3 lbs per sq ft.
- West Coast Hemlock: 1 to 1.5 lbs per sq ft. Above 1.5, the infill shows.
The lower figure is the minimum. Use the upper figure for dog areas, heavy traffic and full sun. Silica Sand comes in 50 lb bags; Turf Armour and Zeo-Odour in 44 lb bags. Example: 560 sq ft of Forest Green Elite at 3 lbs is 1,680 lbs, or 34 bags of silica. See PGB infill options.
Spikes. Use 6 in galvanized spikes, or 4 in where the ground will not take a 6 in spike. Count one every 6 in around the perimeter, set 2 in in from the edge, plus one per square foot through the field. Count each seam’s temporary holding spikes separately; they come back out.
Seam tape. Use 6 in tape for ordinary lawn seams and 10 in tape for play areas, dog runs, sports areas and putting greens. Both come in 33 ft rolls. Convert the total seam length into rolls and round up.
Confirm stock before quoting
Send PGB the selected turf line and labelled cutting plan before issuing the quote. Confirm stock for the actual pieces required, not just the total area, along with the infill, spikes and seam tape.
Premium Grass Blades supplies an artificial turf range and installation accessories; it does not install. Independent installers contract directly with their customers.
Keep the supplier confirmation with the drawing so the quoted materials can be checked against the eventual order. A change of turf line, roll width or piece layout should trigger a revised takeoff before the quote is finalised.
Professional takeaway
Estimate the pieces first and the area second. A labelled cutting plan with matching pile-direction arrows gives the turf order and accessory list a shared basis.
Related questions
Can I order turf using only the site’s square footage?
No. Square footage does not show whether roll-width pieces will fit, where seams belong or how much material is trimmed away. Ordering by area is the most common way a job comes up short.
When can an offcut be reused?
Only when it fits with the same pile direction and has enough material for trimming. Assign each one a specific place on the drawing before reducing the order.
Should infill be based on all the turf purchased?
No. Use the finished turf area receiving infill, not offcuts, and the rate for the selected turf.
Related articles
- Why Proper Planning Happens Before Any Turf Is Installed
- Understanding Artificial Turf Specifications (Blade Height, Face Weight, Density)
- Why Base Preparation Is the Most Critical Step in Turf Installation
Speak with the PGB team
Call 604-757-2899 or email [email protected] with your sketch and cutting schedule to confirm stock and accessories.